    1  "Be printing."  "1.The last printting task haven't finished,retry after  moment.	 2.Abort software process.Restart programme." 

    2  "The start pass index is bigger than task pass total."  "The restore print paramter is error!	 " 

    3  "No authorization,No printing"  "Contact your equipment provider." 

    4  "Detected system configuration exist error!"  "Contact your equipment provider! " 

    5  "PrintHead Voltage Exception!"  "" 

    6  "Failed to generate step calibration image."  "Is the disk remainder space enough ?Confirm pls." 

    7  "GrayScale Setting failed"  "Please check system connection or cable comunication " 

    9  "Busing for other processing. Retry after a moment!"  "" 

   10  "The process of last printting task is executing"  "1.The last printting task has not finished,retry after  moment.	 2.Close process.Restart programme." 

   11  "The special rip source isn't exist."  "1.Special rip file can't to read.	 2.The net rip data stream is interrupted" 

   12  "The color count can't be supported by printer."  "The color count of special rip source over system capacity.	 " 

   14  "The resolution of rip source  can't be supported by printer."  "The XDPI of rip source  over  system capacity." 

   15  "The parameter of printhead data channal is wrong."  "The system configuration exist some errors,the configuration  file possible exist fatal error.restore backup configuration or reinstall software. please!	 " 

   16  "The channal count is wrong."  "The system configuration exist some errors,the configuration  file possible exist fatal error.restore backup configuration or reinstall software. please!	 	 " 

   17  "The parameter of printhead data channal is wrong."  "The system configuration exist some errors,the configuration  file possible exist fatal error.restore backup configuration or reinstall software. please!	 	 " 

   18  "The parameter of printhead data channal is wrong."  "The system configuration exist some errors,the configuration  file possible exist fatal error.restore backup configuration or reinstall software. please!	 " 

   19  "Memory lack!"  "Close some application which is used much memory.	 " 

   21  "The print mode can't  be supported  by system."  "Attempt to change print mode,restart print." 

   22  "The printting length of current task is bigger than material."  "1.Sure to validity of material width.	 2.Update more broad material.	 3.Use region printting." 

   23  "The system refuse to print,beause the length of print will exceed printer max motion length"  "1.Increase printting motion buffer length.	 2.System configuration have some error.reinstall software." 

   27  "Capping can not back zero"  "Please check cap motion system" 

   28  "carriage is not at safety height"  "Please check lifter postion ,if it under the flatbed" 

   50  "Carriage can't go to home position."  "1.The motion system isn't normalcheck eletricity  Please check electrocircuit!	 2.The carriage position encoder isn't work,verify please!" 

   61  "Carriage can't go to home position."  "1.The motion system isn't normalcheck eletricity  Please check electrocircuit!	 2.The carriage position encoder isn't work,verify please!" 

   62  "Can't found material."  "Verify sensor is normal please." 

   63  "Occur error in Measuring material."  "Only found portion borderCheck sensor." 

   79  "Failed to add task to print queue."  "1.File is using by other process.	 2.File format is incorrect." 

   79  "Rip file can't support "  "Check  rip driver libaray	 " 

   80  "Failed to process rip file."  "" 

  100  "Specified rip file can't supported by system.."  "System don't include specified rip format supported table.if you have the speciaied rip supported packet file,you can import this file by software." 

  111  "The control device can't be driven!"  "1.Reconnection USB controll card.	 2.Usb card is damaged." 

  112  "The main card firmware can't be load."  "The main card maybe damaged." 

  113  "The motion cotroll don't work normally."  "The main card maybe damaged." 

  116  "Carriage card found error."  "Contact your equipment provider" 

  117  "Carriage card exist voltage error! "  "Contact your equipment provider.please!" 

  118  "Failed to create filber communication."  "check carriage card is work normally.	 " 

  120  "The reset action is cancel by user,the carriage orientation isn't work,Don't to execute motion move."  "" 

  121  "System can't detect the valid  signal of limit switch.Failed to reset system."  "Verify the connection between electrocircuit and limit switch ." 

  122  "System can't detect the signal of carriage  position encoder in reset actionFailed to reset action ."  "1.Verify motion work is normal.	 2.Verify connection between electrocircuit and carriage position encoder." 

  123  "The signal phase of carriage position encoder is inverse."  "Verify encoder signal  A and  B ." 

  124  "Two direction limit switch signals are valid."  "1.Verify servo card is normal.	 2.Verify connection between servo card and limit switch ." 

  125  "Detected emergency signal."  "Close emergency switch,then restart software." 

  131  "Failed to check material encoder."  "Verify conection of encoder device." 

  132  "The phase signal of material advance encoder is converted."  "" 

  133  "No position encoder signal."  "the main board exist some problem." 

  134  "The position phase signal of motion control is converted."  "convert A and B phase signal connection." 

  135  "Failed to check step advance encoder."  "The Encoder maybe exist installing problem." 

  140  "It isn't match between software and control card."  "Contact your equipment provider! " 

  141  "The authorization data is incorrect.System can't work normally!"  "Contact your equipment provider.please!" 

  142  "Failed to get authorization information.the system can't work normally!"  "Contact your equipment provider.please" 

  143  "PrintHead card can't  match with main control card!"  "" 

  144  "Failed to load moving card information!"  "" 

  145  "The authorization is limitation . System time is incorrect."  "Confirm current system time is correct." 

  146  "The authorization is limitation . System time is incorrect."  "Confirm current system time is correct." 

  147  "The authorization is limit time,Now is expired.the system can't work."  "Contact your equipment provider.please!" 

  148  "The authorization is limit use count,Now is expired.the sysytem can't work"  "Contact your equipment provider.please!" 

  151  "No found security dog."  "Check wheather security dog is setuped.	 " 

  152  "This security dog is invalid."  "The security dog don't match control hardware.	 " 

  153  "Failed to verify security data verified."  "Contact your equipment provider.	 	 " 

  154  "The security dog time is wrong!"  "Contact your equipment provider.	 	 " 

  155  "The Security dog has exprired."  "Contact your equipment provider	 	 " 

  156  "The Security dog has exprired."  "Contact your equipment provider	 	 " 

  157  "The Stage is expired."  "Contact your equipment provider to get new stage password." 

  159  "The security dog time is wrong!"  "Contact your equipment provider.	 	 " 

  160  "Ths language of software isn't authorization"  "Contact your equipment provider.	 	 " 

  161  "The authorization is unactive.must input actived password and restart software!"  "Contact your eqiupment provier to get actived password." 

  168  "The stage password is wrong!"  "Contact your equipment provider to get password!" 

  169  "The new stage is expired.continue to input valid password.please"  "Contact your equipment provider to get password!" 

  260  "Failed adjust carriage move parameter"  "1.Verify ths carriage work is normally.	 2.Verify the carriage encoder work is normally." 

  261  "Failed adjust advance move parameter"  "1.Verify ths material advance work is normally.	 2.Verify the material advance encoder work is normally." 

  301  "The printting task data source is disconnected."  "Verify rip data source provider,for example net client,rip file." 

  302  "The printting task data source is disconnected."  "Verify rip data source provider,for example net client,rip file." 

  303  "The printting task data source is disconnected."  "Verify rip data source provider,for example net client,rip file." 

  304  "The printting task data source is disconnected."  "Verify rip data source provider,for example net client,rip file." 

  305  "The printting task data source is disconnected."  "Verify rip data source provider,for example net client,rip file." 

  310  "The motion move instruction length is longer than machine legnth,or carriage can't move appointed position,printting is breaked  down."  "1.Verify motion work is normal.	 2.Verify connection between electrocircuit and carriage position encoder." 

  385  "Printing without data"  "current setting close color,white and varnlish data" 

  401  "Failed to backup printting parameter."  "" 

  402  "Failed to backup printting parameter."  "The dest file can't be write." 

  403  "The format of import parameter file is incorrect.cancel operation."  "The file format is incorrect." 

